[No public or meaningful name is available]

Guidance on Safe Use

First-aid measures

General advice : Take Risk and Safety phrases (section 15) into account.

Inhalation : Remove from exposure site to fresh air and keep at rest. Obtain medical advice.

Skin contact : Remove contaminated clothes. Wash thoroughly with water (and soap). Contact physician if symptoms persist.

Eye contact : Flush immediately with water for at least 15 minutes. Contact physician if symptoms persist.

Ingestion : Rinse mouth with water and obtain medical advice.

Fire-fighting measures

Suitable extinguishing media : Carbondioxide, dry chemical, foam.

Extinguishing media which shall not be used for safety reasons : Do not use a direct waterjet on burning material.

Accidental release measures

Personal precautions : Avoid inhalation and contact with skin and eyes. A self-contained breathing apparatus is recommended in case of a major spill.

Environmental precautions : Keep away from drains, surface- and groundwater and soil.

Methods for cleaning up : Clean up spillage promptly. Remove ignition sources. Provide adequate ventilation. Avoid excessive inhalation of vapours. Gross spillages should be contained by use of sand or inert powder and disposed of according to the local regulations.

Handling and storage

Handling

Advice on safe handling : Avoid excessive inhalation of concentrated vapors. Follow good manufacturing practices for housekeeping and personal hygiene. Wash any exposed skin immediately after any chemical contact, before breaks and meals, and at the end of each work period. Contaminated clothing and shoes should be thoroughly cleaned before re-use.

If appropriate, procedures used during the handling of this material should also be used when cleaning equipment or removing residual chemicals from tanks or other containers, especially when steam or hot water is used, as this may increase vapor concentrations in the workplace air. Where chemicals are openly handled, access should be restricted to properly trained employees.

Keep all heated processes at the lowest necessary temperature in order to minimize emissions of volatile chemicals into the air.

Advice on protection against fire and explosion : Keep away from ignition sources and naked flame.

 

Storage

Requirements for storage areas and containers : Store in a cool, dry, ventilated area away from heat sources. Keep containers upright and tightly closed when not in use.

Transport information

Land transport (UN RTDG/ADR/RID)

UN number:

UN 3802

Shipping information

Proper shipping name and description:

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.

Chemical name:

1-((4,4,8-trimethyltricyclo[6.3.1.02,5]dodecan-1-yl)oxy)pentan-2-ol

Language:

English

SpecialProvisions

Inland waterway transport (UN RTDG/ADN(R))

UN number:

UN 3802

Shipping

Remarks

Marine transport (UN RTDG/IMDG)

UN number:

3802

Shipping information

Proper shipping name and description:

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.

Chemical name:

1-((4,4,8-trimethyltricyclo[6.3.1.02,5]dodecan-1-yl)oxy)pentan-2-ol

Language:

English

Remarks

Air transport (UN RTDG/ICAO/IATA)

Shipping information

Proper shipping name and description:

ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.

Chemical name:

1-((4,4,8-trimethyltricyclo[6.3.1.02,5]dodecan-1-yl)oxy)pentan-2-ol

Language:

English

Remarks

SpecialProvisions

Exposure controls / personal protection

Engineering measures
Where appropriate, use closed systems to transfer and process this material.
If appropriate, isolate mixing rooms and other areas where this material is used or openly han-dled. Maintain these areas under negative air pressure relative to the rest of the plant.
Personal protective equipment
Eye protection
:
Use tight-fitting goggles, face shield or safety glasses with side shields if eye contact might occur.
Equipment should conform to EN 166
Hand protection
Remarks
:
Avoid skin contact. Use chemically resistant gloves. The se-lected protective gloves have to satisfy the specifications of Regulation (EU) 2016/425 and the standard EN 374 derived from it. Be aware that in daily use the durability of a chemical resistant protective glove can be notably shorter than the break through time measured according to EN 374, due to the numerous outside influences (e.g. temperature). Please observe the instructions regarding permeability and break-through time which are provided by the supplier of the gloves. Also take into consideration the specific local conditions un-der which the product is used, such as the danger of cuts, abrasion, and the contact time. The choice of an appropriate glove does not only depend on its material but also on other quality features and is different from one producer to the oth-er.
Skin and body protection
:
Choose body protection in relation to its type, to the concen-tration and amount of dangerous substances, and to the spe-cific work-place.
Respiratory protection
:
Use local exhaust ventilation around open tanks and other open sources of potential exposures in order to avoid exces-sive inhalation, including places where this material is openly weighed or measured. In addition, use general dilution venti-lation of the work area to eliminate or reduce possible worker exposures.
No respiratory protection is required during normal operations in a workplace where engineering controls such as adequate ventilation, etc. are sufficient.
If engineering controls and safe work practices are not suffi-cient, an approved, properly fitted respirator with organic va-por cartridges or canisters and particulate filters should be used:

Stability and reactivity

Stable under normal conditions.

Disposal considerations

Product:
Dispose of according to local regulations. Avoid disposing into drainage systems and into the environment.
Contaminated packaging:Empty containers should be taken to an approved waste han-dling site for recycling or disposal.