Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

General information Instantly remove any clothing soiled by the product.
- After inhalation Supply fresh air or oxygen; call for doctor.
- After skin contact
Instantly wash with water and soap and rinse thoroughly.
If skin irritation continues, consult a doctor.
- After eye contact
Rinse opened eye for several minutes (10 - 15) under running water. Then consult doctor.
Use eye protection.
- After swallowing Do not induce vomiting; instantly call for medical help.

Fire-fighting measures

5.1 Extinguishing media
- Suitable extinguishing agents
CO2, extinguishing powder or water jet. Fight larger fires with water jet or alcohol-resistant foam.
- For safety reasons unsuitable extinguishing agents Do not use a heavy water stream.
- 5.2 Special hazards arising from the substance or mixture
Formation of toxic gases is possible during heating or in case of fire.
Can be released in case of fire
Hydrogen chloride (HCl)
- 5.3 Advice for firefighters
- Protective equipment:
Wear self-contained breathing apparatus.
Do not inhale explosion gases or combustion gases.
Wear full protective suit.
- Additional information
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.

Accidental release measures

- 6.1 Personal precautions, protective equipment and emergency procedures
Wear protective clothing (described in section 8).
Avoid causing dust.
Do not inhale dust.
Avoid contact with substance.
- 6.2 Environmental precautions: Do not allow to enter drainage system, surface or ground water.
- 6.3 Methods and material for containment and cleaning up:
Collect mechanically.
Dispose of contaminated material as waste according to item 13.
Ensure adequate ventilation.
Send for recovery or disposal in suitable containers.

Handling and storage

- 7.1 Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Work only in fume cupboard.
Prevent formation of dust.
- Information about protection against explosions and fires: No special measures required.
- 7.2 Conditions for safe storage, including any incompatibilities
- Storage
- Requirements to be met by storerooms and containers: No special requirements.
- Information about storage in one common storage facility: Not required.
- Further information about storage conditions:
Keep container tightly closed.
Store in cool, dry conditions in well sealed containers.

Transport information

Land transport (UN RTDG/ADR/RID)

UN number:
n.a.
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (UN RTDG/ADN(R))

UN number:
n.a.
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

UN number:
n.a.
Shippingopen allclose all
Remarksopen allclose all

Air transport (UN RTDG/ICAO/IATA)

UN number:
n.a.
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

- 8.1 Control parameters
- Components with limit values that require monitoring at the workplace: Not required.
- DNELs (Derived no-effect level) No information available
- PNECs (predicted no effect concentration) No information available
- Additional information: The lists that were valid during the compilation were used as basis.
- 8.2 Exposure controls
- Personal protective equipment
- General protective and hygienic measures
The usual precautionary measures should be adhered to general rules for handling chemicals.
Keep away from foodstuffs, beverages and food.
Take off immediately all contaminated clothing
Wash hands during breaks and at the end of the work.
Avoid contact with the eyes and skin.
Do not inhale dust
- Breathing equipment: Use breathing protection only if dust is formed.
- Recommended filter device for short term use:
Filter P1
- Protection of hands:
Protective gloves (EN 374).
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/
the chemical mixture.
To avoid skin problems reduce the wearing of gloves to the required minimum.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
degradation
- Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer.
- Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
observed.
- Eye protection:
Tightly sealed safety glasses.
- Body protection: Protective work clothing.

Stability and reactivity

- 10.1 Reactivity No further relevant information available.
- 10.2 Chemical stability
- Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
- 10.3 Possibility of hazardous reactions No dangerous reactions known
- 10.4 Conditions to avoid No further relevant information available.
- 10.5 Incompatible materials: No further relevant information available.
- 10.6 Hazardous decomposition products: No dangerous decomposition products known

Disposal considerations

- 13.1 Waste treatment methods
- Recommendation
Hand over to disposers of hazardous waste.
Chemicals must be disposed of in compliance with restrictive national regulations.
- Uncleaned packagings:
- Recommendation:
Disposal must be made according to official regulations.
Packaging must be disposed of in compliance with country-specific regulations or must be passed to a
packaging return system.
- Recommended cleaning agent: Water, if necessary with cleaning agent.