Registration Dossier

Administrative data

First-aid measures

- 4.1 Description of first aid measures
- General information Instantly remove any clothing soiled by the product.
- After inhalation Supply fresh air; consult doctor in case of symptoms.
- After skin contact Instantly wash with water and soap and rinse thoroughly.
- After eye contact Rinse opened eye for several minutes (10 - 15)under running water.
- After swallowing Instantly call for doctor.
- 4.2 Most important symptoms and effects, both acute and delayed No further relevant information available.
- 4.3 Indication of any immediate medical attention and special treatment needed
No further relevant information available.

Fire-fighting measures

- 5.1 Extinguishing media
- Suitable extinguishing agents
CO2, extinguishing powder or water jet. Fight larger fires with water jet or alcohol-resistant foam.
- For safety reasons unsuitable extinguishing agents Do not use a heavy water stream.
- 5.2 Special hazards arising from the substance or mixture
Can be released in case of fire
Carbon monoxide (CO), carbon dioxide (CO2)
Hydrogen chloride (HCl)
Hydrogen fluoride (HF)
- 5.3 Advice for firefighters
- Protective equipment:
Wear self-contained breathing apparatus.
Do not inhale explosion gases or combustion gases.
Wear full protective suit.
- Additional information
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.

Accidental release measures

- 6.1 Personal precautions, protective equipment and emergency procedures
Use breathing protection against the effects of fumes/dust/aerosol.
- 6.2 Environmental precautions: Do not allow to enter drainage system, surface or ground water.
- 6.3 Methods and material for containment and cleaning up:
Absorb with liquid-binding material (sand, diatomite, acid binders, universal binders).
Dispose of contaminated material as waste according to item 13.
Ensure adequate ventilation.

Handling and storage

- 7.1 Precautions for safe handling
Ensure good ventilation/exhaustion at the workplace.
Prevent formation of aerosols.
- Information about protection against explosions and fires: No special measures required.
- 7.2 Conditions for safe storage, including any incompatibilities
- Storage
- Requirements to be met by storerooms and containers: No special requirements.
- Information about storage in one common storage facility: Not required.
- Further information about storage conditions: Store in cool, dry conditions in well sealed containers.
- 7.3 Specific end use(s) No further relevant information available.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

- Additional information about design of technical systems: No further data; see item 7.
- 8.1 Control parameters
- Components with limit values that require monitoring at the workplace: Not required.
- DNELs (Derived no-effect level) No information available
- PNECs (predicted no effect concentration) No information available
- 8.2 Exposure controls
- Personal protective equipment
- General protective and hygienic measures
The usual precautionary measures should be adhered to general rules for handling chemicals.
Keep away from foodstuffs, beverages and food.
Wash hands during breaks and at the end of the work.
Do not inhale fumes
- Breathing equipment:
In case of brief exposure or low pollution use breathing filter apparatus. In case of intensive or longer
exposure use breathing apparatus that is independent of circulating air.
- Recommended filter device for short term use: Filter A (acc. to EN 141) for organic vapours and gases; boiling piont > 65 °C
- Protection of hands: Not required. Use recommended.
- Material of gloves: The selection of the suitable gloves does not only depend on the material, but also on further
marks of quality and varies from manufacturer to manufacturer.
- Penetration time of glove material: The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
- Eye protection: Safety glasses
- Body protection: Protective work clothing.

Stability and reactivity

- 10.1 Reactivity No further relevant information available.
- 10.2 Chemical stability
- Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
- 10.3 Possibility of hazardous reactions No dangerous reactions known
- 10.4 Conditions to avoid No further relevant information available.
- 10.5 Incompatible materials:
Strong oxidizing materials
- 10.6 Hazardous decomposition products:
Hydrogen chloride (HCl) / hydrochloric acid
Fluorinated hydrocarbons
Hydrogen fluoride

Disposal considerations

- 13.1 Waste treatment methods
- Recommendation
After prior treatment product has to be disposed of in an incinerator for hazardous waste under adherence to
the regulations pertaining to the disposal of particularly hazardous waste.
- Uncleaned packagings:
- Recommendation:
Disposal must be made according to official regulations.
Packaging must be disposed of in compliance with country-specific regulations or must be passed to a
packaging return system.
Empty contaminated packagings thoroughly. They can be recycled after thorough and proper cleaning.
Packagings that cannot be cleaned are to be disposed of in the same manner as the product.
15 01 10: packaging containing residues of or contaminated by dangerous substances