Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

Eye Contact: Flush with water while holding eyelids open for at least 15 minutes. Seek medical attention immediately.
Skin Contact: Remove contaminated clothing. Flush area with large amounts of water. Use soap. Seek medical attention.
Ingestion: Never give anything by mouth to an unconscious person. Wash out mouth with water. Do not
induce vomiting unless directed by medical personnel. Seek medical attention immediately.
Inhalation: Remove to fresh air and keep patient at rest. Seek medical attention immediately

Fire-fighting measures

Extinguishing Media: Extinguish fires with CO2, extinguishing powder, foam, or water.

Special Hazards Arising from the Substance or Mixture Hazardous Combustion Products: Formation of toxic gases is possible during heating or fire. May include oxides of carbon and nitrogen.

Fire / Explosion Hazards: Fine particles (such as dust and mists) may fuel fires/explosions.

Advice for Fire-Fighters:
During all fire fighting activities, wear appropriate protective equipment, including self-contained breathing apparatus

Accidental release measures

Personal Precautions, Protective Equipment and Emergency Procedures: Personnel involved in clean-up should wear appropriate personal protective equipment (see Section 8). Minimize exposure.
Environmental Precautions: Place waste in an appropriately labeled, sealed container for disposal. Care should be taken to avoid environmental release.
Measures for Cleaning/Collecting: Contain the source of the spill if it is safe to do so. Collect spilled material by a method that controls dust generation. Avoid use of a filtered vacuum to clean spills of dry solids. Clean spill
area thoroughly.
Additional Consideration for Large Spills: Non-essential personnel should be evacuated from affected area. Report emergency situations immediately. Clean up operations should only be undertaken by trained personnel.

Handling and storage

Precautions for Safe Handling:
Ground and bond all bulk transfer equipment. Avoid open handling. Minimize dust generation. Use local exhaust ventilation or perform work under fume hood/fumecupboard. Avoid inhalation and contact with skin, eye, and clothing. When handling, use appropriate personal protective equipment (see Section 8). Wash hands and any exposed skin after removal of PPE. Releases to the environment should be avoided. Review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure or environmental releases. Potential points of process emissions of this material to the atmosphere should be controlled with dust collectors, HEPA filtration systems or other equivalent controls.

Conditions for Safe Storage, Including any Incompatibilities Storage Conditions: Store at room temperature in properly labeled containers. Keep away from heat, sparks and
flames.

Transport information

Land transport (UN RTDG/ADR/RID)

UN number:
Not regulated under ADR/RID
Shippingopen allclose all
SpecialProvisionsopen allclose all

Inland waterway transport (UN RTDG/ADN(R))

UN number:
Not regulated under ADN(R)
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

UN number:
Not regulated under IMIG
Shippingopen allclose all
Remarksopen allclose all

Air transport (UN RTDG/ICAO/IATA)

UN number:
Not regulated under ICAO/IATA
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

OEB 3 (control exposure to the range of 10ug/m3 to < 100ug/m3)

Exposure Controls
Engineering Controls: Engineering controls should be used as the primary means to control exposures. Use process containment, local exhaust ventilation, or other engineering controls to maintain airborne levels within the OEB range.

Personal Protective Equipment:
Refer to applicable national standards and regulations in the selection and use of personal protective equipment (PPE). Contact your safety and health professional or safety equipment
supplier for assistance in selecting the correct protective clothing/equipment based on an assessment of the workplace conditions, other chemicals used or present in the workplace and
specific operational processes.

Hands: Wear impervious gloves (e.g. Nitrile, etc.) as minimum protection. (Protective gloves must meet the standards in accordance with EN374, ASTM F1001 or international equivalent.)

Eyes: Wear safety glasses as minimum protection. (Safety glasses must meet the standards in accordance with EN166, ANSI Z87.1 or international equivalent.)

Skin: Wear impervious protective clothing when handling this compound. (Protective clothing must meet the standards in accordance with EN13982, ANSI 103 or international equivalent.)

Respiratory protection: Under normal conditions of use, if the applicable Occupational Exposure Band (OEB) is exceeded, wear an appropriate respirator with a protection factor sufficient to control exposures to below the OEB (e.g. particulate respirator with a half mask, P3 filter). (Respirators must meet the standards in accordance with EN140, EN143, ASTM F2704-10 or international equivalent.)

Stability and reactivity

Reactivity: No data available
Chemical Stability: Stable under normal conditions of use.

Possibility of Hazardous Reactions
Oxidizing Properties: No data available
Conditions to Avoid: Fine particles (such as dust and mists) may fuel fires/explosions. As a precautionary measure,
keep away from heat sources and electrostatic discharge.
Incompatible Materials: As a precautionary measure, keep away from strong oxidizers

Hazardous Decomposition Products: No data available

Disposal considerations

Dispose of waste in accordance with all applicable laws and regulations. Member State specific and Community specific provisions must be considered. Considering the relevant known environmental and human health hazards of the material, review and implement appropriate technical and procedural waste water and waste disposal measures to prevent occupational exposure and environmental release. It is recommended that waste minimization be practiced. The best available technology should be utilized to prevent environmental releases. This may include destructive techniques for waste and wastewater.

Categories Display