Registration Dossier

Administrative data

First-aid measures

- 4.1 Description of first aid measures
- General information
Instantly remove any clothing soiled by the product.
Symptoms of poisoning may even occur after several hours; therefore medical observation for at least 48
hours after the accident.
- After inhalation In case of unconsciousness bring patient into stable side position for transport.
- After skin contact Instantly wash with water and soap and rinse thoroughly.
- After eye contact
Rinse opened eye for several minutes (10 - 15) under running water. Then consult doctor.
Use eye protection.
- After swallowing Instantly call for doctor.
- 4.2 Most important symptoms and effects, both acute and delayed Dazed, lightheadedness
- 4.3 Indication of any immediate medical attention and special treatment needed
No further relevant information available.

Fire-fighting measures

- 5.1 Extinguishing media
- Suitable extinguishing agents
CO2, extinguishing powder or water jet. Fight larger fires with water jet or alcohol-resistant foam.
- 5.2 Special hazards arising from the substance or mixture No further relevant information available.
- 5.3 Advice for firefighters
- Protective equipment:
Wear self-contained breathing apparatus.
Do not inhale explosion gases or combustion gases.
Wear full protective suit.
- Additional information
Dispose of fire debris and contaminated fire fighting water in accordance with official regulations.

Accidental release measures

- 6.1 Personal precautions, protective equipment and emergency procedures
Wear protective clothing (described in section 8).
Avoid contact with substance.
Use only explosion-protected devices and tools free of spark use.
Ignition sources, sparking and flames avoid.
- 6.2 Environmental precautions: Do not allow product to reach sewage system or water bodies.
- 6.3 Methods and material for containment and cleaning up:
Dispose of contaminated material as waste according to item 13.
Send for recovery or disposal in suitable containers.

Handling and storage

- 7.1 Precautions for safe handling
This product is to handle exclusive under strictly controlled conditions in accordance with Regulation (EC)
No.1907/2006 (REACH), article 18(4).
- Information about protection against explosions and fires:
Protect from heat.
Protect against electrostatic charges.
- 7.2 Conditions for safe storage, including any incompatibilities
- Storage
- Requirements to be met by storerooms and containers: No special requirements.
- Information about storage in one common storage facility: Not required.
- Further information about storage conditions:
Store in cool, dry conditions in well sealed containers.
Protect from heat and direct sunlight.
- Storage class VCI class 3
- 7.3 Specific end use(s) No further relevant information available.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

- Additional information about design of technical systems: No further data; see item 7.
- 8.1 Control parameters
- Components with limit values that require monitoring at the workplace: Not required.
- Additional information: The lists that were valid during the compilation were used as basis.
- 8.2 Exposure controls
- Personal protective equipment
- General protective and hygienic measures
The usual precautionary measures should be adhered to general rules for handling chemicals.
Keep away from foodstuffs, beverages and food.
Take off immediately all contaminated clothing
Wash hands during breaks and at the end of the work.
Avoid contact with the skin.
Avoid contact with the eyes and skin.
Do not eat, drink or smoke while working.
- Breathing equipment: Not required.
- Recommended filter device for short term use:
The entrepreneur has to ensure that maintenance, cleaning and testing of respiratory protective devices are
carried out according to the instructions of the manufacturer. These measures have to be properly
- Protection of hands:
Protective gloves (EN 374).
The glove material has to be impermeable and resistant to the product/ the substance/ the preparation.
Due to missing tests no recommendation to the glove material can be given for the product/ the preparation/
the chemical mixture.
To avoid skin problems reduce the wearing of gloves to the required minimum.
Selection of the glove material on consideration of the penetration times, rates of diffusion and the
- Material of gloves
The selection of the suitable gloves does not only depend on the material, but also on further marks of quality
and varies from manufacturer to manufacturer.
- Penetration time of glove material
The exact break trough time has to be found out by the manufacturer of the protective gloves and has to be
The times listed are suggested by measurements taken at 22 degree C and constant contact. Temperatures
raised by warmed substances, body heat, etc. and a weakening of the effective layer thickness caused by
expansion can lead to a significantly shorter breakthrough time.
In case of doubt contact the gloves' manufacturer.
A 1.5-times increase / decrease in the layer thickness doubles / halves the breakthrough time. This data only
applies to the pure substance. Transferred to mixtures of substances, these figures should only be taken as an
aid to orientation.
- Remark:
This recommendation applies only to the product stated in the safety data sheet. When dissolving in or mixing
this substance with other substances and under conditions deviating from those stated in EN 374, please
contact the supplier of CE –approved gloves.
- Eye protection:
Safety glasses
- Body protection:
Protective work clothing.
Protective clothing should be selected specifically for the working place, depending on concentration and
quantity of the hazardous substances handeld. The resistance of the protective clothing to chemicals should
be ascertained with the respective supplier.

Stability and reactivity

- 10.1 Reactivity No further relevant information available.
- 10.2 Chemical stability
- Thermal decomposition / conditions to be avoided: No decomposition if used according to specifications.
- 10.3 Possibility of hazardous reactions No dangerous reactions known
- 10.4 Conditions to avoid No further relevant information available.
- 10.5 Incompatible materials: No further relevant information available.
- 10.6 Hazardous decomposition products: No dangerous decomposition products known

Disposal considerations

- 13.1 Waste treatment methods
- Recommendation
Hand over to disposers of hazardous waste.
Chemicals must be disposed of in compliance with restrictive national regulations.
- Uncleaned packagings:
- Recommendation:
Disposal must be made according to official regulations.
Packaging must be disposed of in compliance with country-specific regulations or must be passed to a
packaging return system.