Registration Dossier

Administrative data

First-aid measures

Description of first aid measures
Remove contaminated or saturated clothing.
Inhalation
Following inhalation of aerosols or mist:
Possible discomfort: irritation of mucous lining (nose, throat, eyes) cough, sneezing, flow of tears.
Move victims into fresh air.
If symptoms persist, consult a physician for treatment.
Skin contact
Wash off immediately with plenty of water.
If symptoms persist, consult a physician for treatment.
Eye contact
Keeping eyelid open, immediately rinse thoroughly for at least 5 minutes using plenty of water or, if necessary, eye rinsing solution.
Consult an ophthalmologist.
Ingestion
Have the mouth rinsed with water.
Have patient drink plenty of water in small sips.
Consult a physician immediately.
Most important symptoms and effects, both acute and delayed
Symptoms
None known
Hazards
None known
Indication of any immediate medical attention and special treatment needed
If required, therapy of irritative effect.
If substance has been swallowed:
Early endoscopy in order to assess mucosa lesions in the oesophagus and stomach which may appear. If necessary, aspirate leftover substance.

Fire-fighting measures

Extinguishing media

Suitable extinguishing media: water spray
foam
carbon dioxide (CO2)
dry powder

Unsuitable extinguishing media: Water
Special hazards arising from the substance or mixture
Hazardous fumes in fires, specific to the product:
nitrogen oxides (NOx)
Advice for firefighters
Water used to extinguish fire should not enter drainage systems, soil or stretches of water.
Ensure there are sufficient retaining facilities for water used to extinguish fire.
Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations.
In case of fire: wear a self contained respiratory apparatus

Accidental release measures

Personal precautions, protective equipment and emergency procedures
Use personal protective equipment
Environmental precautions
Do not allow entrance in sewage water, soil stretches of water, groundwater, drainage systems.
Methods and material for containment and cleaning up
Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust).
Fill into marked, sealable containers.
To be disposed of in compliance with existing regulations.

Suitable binder: sand (for damming up), sawdust, universal absorbent

Handling and storage

Precautions for safe handling
Provide good ventilation or extraction.
Avoid contact with skin and eyes.
Conditions for safe storage, including any incompatibilities
Advice on protection against fire and explosion
Normal measures for preventive fire protection.
Storage
Keep containers tightly closed in a cool, well-ventilated place.
Protect from moisture.

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Special provisions / remarks
Remarks:
Not dangerous according to transport regulations.
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Exposure controls
Engineering measures
Provide for good ventilation if vapours/aerosols are formed.
Personal protective equipment
Respiratory protection
In case of dusts/vapours/aerosols being formed or if the limit values like TLV are exceeded:
use respiratory equipment with suitable filter (filter type ABEK) or wear a self contained respiratory apparatus
Use only respiratory protection equipment with CE-symbol including four digit test number.
The filter class for the respirator must be suitable for the maximum expected contaminant concentration (gas/vapour/aerosol/particulates) that may arise when handling the product. If this concentration is exceeded, self-contained breathing apparatus must be used.
Note time limit for wearing respiratory protective equipment.
Hand protection
Glove material for example, butyl-rubber
Material thickness 0,5 mm
Break through time >= 480 min
Glove material for example, Fluorinated rubber (Viton)
Material thickness 0,4 mm
Break through time >= 480 min
Selection of protective gloves to meet the requirements of specific workplaces.
Suitability for specific workplaces should be clarified with protective glove manufacturers.
The information is based on our own tests, references from the literature and information from glove manufacturers, or derived by analogy with similar materials.
Please observe that the daily duration of usage of a chemical protective glove is in practice far shorter due to the many influencing factors (e.g. temperature, mechanical strain on the glove material) than the permeation time determined acc. EN 374.
Eye protection
close-fitting protective goggles (e.g. closed goggles)
Skin and body protection
No special protective equipment required.
Hygiene measures
When using, do not eat, drink or smoke. Wash face and/or hands before break and end of work.
Remove contaminated or saturated clothing.
Wash contaminated clothing before reuse.
Protective measures
Handle in accordance with good industrial hygiene and safety practices.
The personal protective equipment used must meet the requirements of directive 89/686/EEC and amendments (CE certification).
If workplace exposure limits are exceeded and/or larger amounts are released (leakage, spilling, dust) the indicated respiratory protection should be used.
If there is the possibility of skin/eye contact, the indicated hand/eye/body protection should be used.
Do not breathe in vapours or aerosols.
Avoid contact with skin and eyes.

Stability and reactivity

Reactivity
No dangerous reaction known under conditions of normal use.
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
Possibility of hazardous reactions No dangerous reactions known.

Conditions to avoid
Protect from moisture.
Incompatible materials
alkalis, alcohols, atmospheric humidity, acids, water
Hazardous decomposition products
Ethanol in case of hydrolysis

Disposal considerations

Waste treatment methods
Product
With respect to local regulations, e.g. dispose of to suitable waste incineration plant.
Uncleaned packaging
Do not reuse empty containers and dispose of in accordance with the regulations issued by the appropriate local authorities.
If there is product residue in the emptied container, follow directions for handling on the container's label.
Incorrect disposal or reuse of this container is illegal and can be dangerous.
Other countries: observe the national regulations.
Waste Key Number
No waste key number as per the European Waste Types List can be assigned to this product, since such classification is based on the (as yet undetermined) use to which the product is put by the consumer.
The waste key number must be determined as per the European Waste Types List (decision on EU Waste Types List 2000/532/EC) in cooperation with the disposal firm / producing firm / official authority.