Registration Dossier

Diss Factsheets

Administrative data

First-aid measures

Description of first aid measures

Immediately remove contaminated clothing. If danger of loss of consciousness, place patient in

recovery position and transport accordingly. Apply artificial respiration if necessary. First aid personnel

should pay attention to their own safety.

If inhaled:

Keep patient calm, remove to fresh air, seek medical attention.

On skin contact:

Wash thoroughly with soap and water.

On contact with eyes:

Immediately wash affected eyes for at least 15 minutes under running water with eyelids held open,

consult an eye specialist.

On ingestion:

Immediately rinse mouth and then drink 200-300 ml of water, seek medical attention.

Indication of any immediate medical attention and special treatment needed

Treatment: Treat according to symptoms (decontamination, vital functions), no known specific

antidote.

Fire-fighting measures

Extinguishing media

Suitable extinguishing media:

carbon dioxide, foam, dry powder

Special hazards arising from the substance or mixture

nitrogen oxides, carbon oxides, amine derivatives

The substances/groups of substances mentioned can be released in case of fire. Under certain

conditions in case of fire other hazardous combustion products may be generated.

Advice for fire-fighters

Special protective equipment:

Wear self-contained breathing apparatus and chemical-protective clothing.

Further information:

Dispose of fire debris and contaminated extinguishing water in accordance with official regulations.

Accidental release measures

Personal precautions, protective equipment and emergency procedures

Avoid inhalation. Avoid contact with the skin, eyes and clothing.

Environmental precautions

Do not discharge into drains/surface waters/groundwater.

Methods and material for containment and cleaning up

For small amounts: Pick up in dry form.

For large amounts: Sweep/shovel up.

Dispose of absorbed material in accordance with regulations.

Handling and storage

Precautions for safe handling

Ensure thorough ventilation of stores and work areas.

Protection against fire and explosion:

Prevent electrostatic charge - sources of ignition should be kept well clear - fire extinguishers should

be kept handy.

Conditions for safe storage, including any incompatibilities

Further information on storage conditions: Avoid all sources of ignition: heat, sparks, open flame. Keep

container tightly closed and in a well-ventilated place. Keep container dry.

Storage stability:

Storage temperature: < 40 °C

Storage duration: 6 Months

Protect against moisture.

From the data on storage duration in this safety data sheet no agreed statement regarding the

warrantee of application properties can be deduced.

Protect from temperatures below: -20 °C

Protect from temperatures above: 40 °C

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all

Exposure controls / personal protection

Personal protective equipment

Respiratory protection:

Breathing protection if dusts are formed.

Hand protection:

Chemical resistant protective gloves (EN 374)

Suitable materials also with prolonged, direct contact (Recommended: Protective index 6,

corresponding > 480 minutes of permeation time according to EN 374):

e.g. nitrile rubber (0.4 mm), chloroprene rubber (0.5 mm), polyvinylchloride (0.7 mm) and other

Manufacturer's directions for use should be observed because of great diversity of types.

Supplementary note: The specifications are based on tests, literature data and information of glove

manufacturers or are derived from similar substances by analogy. Due to many conditions (e.g.

temperature) it must be considered, that the practical usage of a chemical-protective glove in practice

may be much shorter than the permeation time determined through testing.

Wear refractive gloves while working with the hot melt.

Eye protection:

Safety glasses with side-shields (frame goggles) (e.g. EN 166)

General safety and hygiene measures

Handle in accordance with good industrial hygiene and safety practice. Wearing of closed work

clothing is required additionally to the stated personal protection equipment. Avoid contact with skin

and eyes.

Stability and reactivity

Reactivity

No hazardous reactions if stored and handled as prescribed/indicated.

Corrosion to metals: Study technically not feasible. Corrosive effects to metal are not

anticipated.

Reactions with

water/air:

Reaction with: water

Flammable gases: no

Toxic gases: no

Corrosive gases: no

Smoke or fog: no

Peroxides: no

Reaction with: air

Flammable gases: no

Toxic gases: no

Corrosive gases: no

Smoke or fog: no

Peroxides: no

Formation of

flammable gases:

Information on hazardous

decomosition products:

Forms no flammable gases in the

presence of water.

Chemical stability

Stable under normal conditions.

Possibility of hazardous reactions

When preparing reactive systems it must be observed that the ratio of retention time to reaction time is

short. Reacts with acids.

Conditions to avoid

Avoid humidity.

Incompatible materials

Substances to avoid:

acids, strong bases

Hazardous decomposition products

No hazardous decomposition products if stored and handled as prescribed/indicated.

Possible decomposition products:

amines

Disposal considerations

Waste treatment methods

Incinerate in suitable incineration plant, observing local authority regulations.

A waste code in accordance with the European waste catalog (EWC) cannot be specified, due to

dependence on the usage.

The waste code in accordance with the European waste catalog (EWC) must be specified in

cooperation with disposal agency/manufacturer/authorities.

Contaminated packaging:

Contaminated packaging should be emptied as far as possible; then it can be passed on for recycling

after being thoroughly cleaned.