Registration Dossier
Registration Dossier
Use of this information is subject to copyright laws and may require the permission of the owner of the information, as described in the ECHA Legal Notice.
EC number: 946-318-1 | CAS number: -
Guidance on Safe Use
Guidance on Safe Use
Administrative data
First-aid measures
Description of first aid measures
Inhalation: Remove exposed person to fresh air if adverse effects are observed.
Eye contact: Any material that contacts the eye should be washed out immediately with water. If easy to do, remove contact lenses.
Skin Contact: Wash with soap and water. If skin irritation occurs, get medical attention.
Ingestion: Treat symptomatically. Get medical attention.
Indication of any immediate medical attention and special treatment needed
Hazards: No data available.
Treatment: Treat symptomatically.
Inhalation: Remove exposed person to fresh air if adverse effects are observed.
Eye contact: Any material that contacts the eye should be washed out immediately with water. If easy to do, remove contact lenses.
Skin Contact: Wash with soap and water. If skin irritation occurs, get medical attention.
Ingestion: Treat symptomatically. Get medical attention.
Indication of any immediate medical attention and special treatment needed
Hazards: No data available.
Treatment: Treat symptomatically.
Fire-fighting measures
General Fire Hazards: No unusual fire or explosion hazards noted.
Extinguishing media Suitable extinguishing media: No data available.
Unsuitable extinguishing media: Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture: A solid stream of water will spread the burning material. Material creates a special hazard because it floats on water.Water may cause splattering.
Advice for firefighters Special fire fighting procedures: No data available.
Special protective equipment for fire-fighters: Recommend wearing self-contained breathing apparatus.
Extinguishing media Suitable extinguishing media: No data available.
Unsuitable extinguishing media: Do not use water jet as an extinguisher, as this will spread the fire.
Special hazards arising from the substance or mixture: A solid stream of water will spread the burning material. Material creates a special hazard because it floats on water.Water may cause splattering.
Advice for firefighters Special fire fighting procedures: No data available.
Special protective equipment for fire-fighters: Recommend wearing self-contained breathing apparatus.
Accidental release measures
Personal precautions, protective equipment and emergency procedures: Personal Protective Equipment must be worn, see Personal Protection Section for PPE recommendations. Ventilate area if spilled in confined space or other poorly ventilated areas.
Environmental Precautions: Avoid release to the environment. Do not contaminate water sources or sewer. Environmental manager must be informed of all major spillages. Prevent further leakage or spillage if safe to do so.
Methods and material for containment and cleaning up: Pick up free solid for recycle and/or disposal.
Environmental Precautions: Avoid release to the environment. Do not contaminate water sources or sewer. Environmental manager must be informed of all major spillages. Prevent further leakage or spillage if safe to do so.
Methods and material for containment and cleaning up: Pick up free solid for recycle and/or disposal.
Handling and storage
Precautions for safe handling: Observe good industrial hygiene practices. Wear appropriate personal protective equipment.
Maximum Handling Temperature: 60 °C
Conditions for safe storage, including any incompatibilities: Store away from incompatible materials.
Maximum Storage Temperature: 60 °C
Maximum Handling Temperature: 60 °C
Conditions for safe storage, including any incompatibilities: Store away from incompatible materials.
Maximum Storage Temperature: 60 °C
Transport information
Land transport (UN RTDG/ADR/RID)
- UN number:
- Not regulated.
Shippingopen allclose all
SpecialProvisionsopen allclose all
Inland waterway transport (UN RTDG/ADN(R))
- UN number:
- Not regulated.
Shippingopen allclose all
Remarksopen allclose all
Marine transport (UN RTDG/IMDG)
- UN number:
- Not regulated.
Shippingopen allclose all
Remarksopen allclose all
Air transport (UN RTDG/ICAO/IATA)
- UN number:
- Not regulated.
Shippingopen allclose all
Remarksopen allclose all
SpecialProvisionsopen allclose all
Exposure controls / personal protection
1. Technical protection measures
None of the components have assigned exposure limits.
2. Organisational protection measures
No special requirements under ordinary conditions of use and with adequate ventilation. Use material in well ventilated area only. Adequate ventilation should be provided so that exposure limits are not exceeded.
Please follow the recommended personal protective equipment (PPE) guidelines below and refer to the appropriate EN standard where applicable. Use personal protective equipment as required.
3. Hand protection
Suitable gloves can be recommended by the glove supplier.
Because specific work environments and material handling practices vary, safety procedures should be specific for each intended application. The correct choice of protective gloves depends upon the chemicals being handled, and the conditions of work and use. Most gloves provide protection for only a limited time before they must be discarded and replaced (even the best chemically resistant gloves will break down after repeated chemical exposures). Gloves should be chosen in consultation with the supplier / manufacturer and taking account of a full assessment of the working conditions. For typical use and handling of chemical substances, gloves should meet the standards set out in EN 374. For applications involving mechanical risks with potential for abrasion or puncture, the standards set out in EN 388 should be considered. For tasks involving thermal hazards, the standards set out in EN 407 should be considered.
Breakthrough time data are generated by glove manufacturers under laboratory test conditions and represent how long a glove can be expected to provide effective permeation resistance. It is important when following breakthrough time recommendations that actual workplace conditions are taken into account. Always consult with your glove supplier for up-to-date technical information on breakthrough times for the recommended glove type.
For continuous contact, we suggest gloves with a minimum breakthrough time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. If suitable gloves are not available to offer that level of protection, gloves with shorter breakthrough times may be acceptable as long as appropriate glove maintenance and replacement regimes are determined and adhered to.
For short-term, transient exposures and splash protection, gloves with shorter breakthrough times may commonly be used. Therefore, appropriate maintenance and replacement regimes must be determined and rigorously followed.
For general applications, we recommend gloves with a thickness typically greater than 0.35 mm.
It is important to note that glove thickness is not the only predictor of glove resistance to a specific chemical, as the permeation efficiency of the glove will be dependent on the exact composition of the glove material. Therefore, glove selection should also be based on consideration of the task requirements and knowledge of breakthrough times.
Glove thickness may also vary depending on the glove manufacturer, the glove type and the glove model. Therefore, the manufacturers’ technical data should always be taken into account to ensure selection of the most appropriate glove for the task.
Note: Depending on the activity being conducted, gloves of varying thickness may be required for specific tasks. For example: Thinner gloves (down to 0.1 mm or less) may be required where a high degree of manual dexterity is needed. However, these gloves are only likely to give short duration protection and would normally be just for single use applications, before being disposed of. Thicker gloves (up to 3 mm or more) may be required where there is a mechanical (as well as a chemical) risk i.e. where there is abrasion or puncture potential.
4. Feet protection
No specific advice
5. Body protection
Long sleeve shirt is recommended. Do not wear rings, watches or similar apparel that could entrap the material.
6. Eye protection
If contact is likely, safety glasses with side shields are recommended. Eye protection should meet the standards set out in EN 166.
7. Respiratory protection
Consult with an industrial hygienist to determine the appropriate respiratory protection for your specific use of this material. A respiratory protection program compliant with all applicable regulations must be followed whenever workplace conditions require the use of a respirator. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites.
Respiratory Protective Equipment (RPE) is not normally required where there is adequate natural or local exhaust ventilation to control exposure.
In case of insufficient ventilation, wear suitable respiratory equipment.
The correct choice of respiratory protection depends upon the chemicals being handled, the conditions of work and use, and the condition of the respiratory equipment.
Safety procedures should be developed for each intended application.
Respiratory protection equipment should therefore be chosen in consultation with the supplier/manufacturer and with a full assessment of the working conditions.
Please refer to the relevant EN standards for the RPE selected.
None of the components have assigned exposure limits.
2. Organisational protection measures
No special requirements under ordinary conditions of use and with adequate ventilation. Use material in well ventilated area only. Adequate ventilation should be provided so that exposure limits are not exceeded.
Please follow the recommended personal protective equipment (PPE) guidelines below and refer to the appropriate EN standard where applicable. Use personal protective equipment as required.
3. Hand protection
Suitable gloves can be recommended by the glove supplier.
Because specific work environments and material handling practices vary, safety procedures should be specific for each intended application. The correct choice of protective gloves depends upon the chemicals being handled, and the conditions of work and use. Most gloves provide protection for only a limited time before they must be discarded and replaced (even the best chemically resistant gloves will break down after repeated chemical exposures). Gloves should be chosen in consultation with the supplier / manufacturer and taking account of a full assessment of the working conditions. For typical use and handling of chemical substances, gloves should meet the standards set out in EN 374. For applications involving mechanical risks with potential for abrasion or puncture, the standards set out in EN 388 should be considered. For tasks involving thermal hazards, the standards set out in EN 407 should be considered.
Breakthrough time data are generated by glove manufacturers under laboratory test conditions and represent how long a glove can be expected to provide effective permeation resistance. It is important when following breakthrough time recommendations that actual workplace conditions are taken into account. Always consult with your glove supplier for up-to-date technical information on breakthrough times for the recommended glove type.
For continuous contact, we suggest gloves with a minimum breakthrough time of 240 minutes, or > 480 minutes if suitable gloves can be obtained. If suitable gloves are not available to offer that level of protection, gloves with shorter breakthrough times may be acceptable as long as appropriate glove maintenance and replacement regimes are determined and adhered to.
For short-term, transient exposures and splash protection, gloves with shorter breakthrough times may commonly be used. Therefore, appropriate maintenance and replacement regimes must be determined and rigorously followed.
For general applications, we recommend gloves with a thickness typically greater than 0.35 mm.
It is important to note that glove thickness is not the only predictor of glove resistance to a specific chemical, as the permeation efficiency of the glove will be dependent on the exact composition of the glove material. Therefore, glove selection should also be based on consideration of the task requirements and knowledge of breakthrough times.
Glove thickness may also vary depending on the glove manufacturer, the glove type and the glove model. Therefore, the manufacturers’ technical data should always be taken into account to ensure selection of the most appropriate glove for the task.
Note: Depending on the activity being conducted, gloves of varying thickness may be required for specific tasks. For example: Thinner gloves (down to 0.1 mm or less) may be required where a high degree of manual dexterity is needed. However, these gloves are only likely to give short duration protection and would normally be just for single use applications, before being disposed of. Thicker gloves (up to 3 mm or more) may be required where there is a mechanical (as well as a chemical) risk i.e. where there is abrasion or puncture potential.
4. Feet protection
No specific advice
5. Body protection
Long sleeve shirt is recommended. Do not wear rings, watches or similar apparel that could entrap the material.
6. Eye protection
If contact is likely, safety glasses with side shields are recommended. Eye protection should meet the standards set out in EN 166.
7. Respiratory protection
Consult with an industrial hygienist to determine the appropriate respiratory protection for your specific use of this material. A respiratory protection program compliant with all applicable regulations must be followed whenever workplace conditions require the use of a respirator. Use self-contained breathing apparatus for entry into confined space, for other poorly ventilated areas and for large spill clean-up sites.
Respiratory Protective Equipment (RPE) is not normally required where there is adequate natural or local exhaust ventilation to control exposure.
In case of insufficient ventilation, wear suitable respiratory equipment.
The correct choice of respiratory protection depends upon the chemicals being handled, the conditions of work and use, and the condition of the respiratory equipment.
Safety procedures should be developed for each intended application.
Respiratory protection equipment should therefore be chosen in consultation with the supplier/manufacturer and with a full assessment of the working conditions.
Please refer to the relevant EN standards for the RPE selected.
Stability and reactivity
Reactivity: No data available.
Chemical Stability: Material is stable under normal conditions.
Possibility of hazardous reactions: Will not occur.
Chemical Stability: Material is stable under normal conditions.
Possibility of hazardous reactions: Will not occur.
Disposal considerations
Disposal methods: Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations. Since emptied containers retain product residue, follow label warnings even after container is emptied.
Contaminated Packaging: Container packaging may exhibit hazards.
Contaminated Packaging: Container packaging may exhibit hazards.
Information on Registered Substances comes from registration dossiers which have been assigned a registration number. The assignment of a registration number does however not guarantee that the information in the dossier is correct or that the dossier is compliant with Regulation (EC) No 1907/2006 (the REACH Regulation). This information has not been reviewed or verified by the Agency or any other authority. The content is subject to change without prior notice.
Reproduction or further distribution of this information may be subject to copyright protection. Use of the information without obtaining the permission from the owner(s) of the respective information might violate the rights of the owner.
