Registration Dossier

Data platform availability banner - registered substances factsheets

Please be aware that this old REACH registration data factsheet is no longer maintained; it remains frozen as of 19th May 2023.

The new ECHA CHEM database has been released by ECHA, and it now contains all REACH registration data. There are more details on the transition of ECHA's published data to ECHA CHEM here.

Diss Factsheets

Guidance on Safe Use

Guidance on Safe Use

Currently viewing:

Administrative data

First-aid measures

Description of first aid measures

General information:

In case of accident or if you feel unwell seek medical advice (show label or SDS where possible).

After contact with the eyes:

Rinse immediately with plenty of water. Seek medical advice in case of continuous irritation.

After contact with the skin:

Wash with plenty of water or water and soap. In the event of a visible skin change or other complaints, seek medical advice (show

label or SDS where possible).

After inhalation:

Provide fresh air.

After swallowing:

Give several small portions of water to drink. Do not induce vomiting.

Most important symptoms and effects, both acute and delayed

Any relevant information can be found in other parts of this section.

Indication of any immediate medical attention and special treatment needed

Further toxicology information must be observed.

Fire-fighting measures

Extinguishing media

Suitable extinguishing media:

water mist , extinguishing powder , alcohol-resistant foam , carbon dioxide , sand .

Extinguishing media which must not be used for safety reasons:

water spray , water jet .

Special hazards arising from the substance or mixture

Risk of hazardous gasses or fumes in the event of fire. Exposure to combustion products may be a health hazard! Hazardous

combustion products: carbon oxides , silicon oxides , incompletely burnt hydrocarbons , toxic and very toxic fumes .

Advice for firefighters

Special protective equipment for fire fighting:

Use respiratory protection independent of recirculated air. Keep unprotected persons away.

Accidental release measures

Personal precautions, protective equipment and emergency procedures

Secure the area. Wear personal protection equipment. Keep unprotected persons away. If material is released

indicate risk of slipping. Do not walk through spilled material.

Environmental precautions

Prevent material from entering surface waters, drains or sewers and soil. Close leak if possible without risk. Contain any fluid that

runs out using suitable material (e.g. earth). Retain contaminated water/extinguishing water. Dispose of in prescribed marked

containers. Inform authorities if substance leaks into surface waters, sewerage or ground.

Methods and material for containment and cleaning up

Take up mechanically and dispose of according to local/state/federal regulations. Do not flush away with water. For small

amounts: Absorb with a neutral (non-acidic / non-basic) liquid binding material such as diatomaceous earth and dispose of

according to government regulations. For large amounts: Liquids may be recovered using suction devices or pumps. If flammable,

only air driven or properly rated electrical equipment should be used. Clean any slippery coating that remains using a detergent /

soap solution or another biodegradable cleaner. Silicone fluids are slippery; spills are a safety hazard. Apply sand or other inert

granular material to improve traction.

Further information:

Exhaust vapours. Eliminate all sources of ignition. Consider explosion protection.

Reference to other sections

Relevant information in other sections has to be considered. This applies in particular for information given on personal protective

equipment and on disposal.

Handling and storage

Precautions for safe handling

Precautions for safe handling:

Ensure adequate ventilation. Must be syphoned off in situ. Spilled substance increases risk of slipping. Avoid formation of

aerosols. In case of aerosol formation special protective measures are required (exhausting by suction, respiratory protection).

Observe information in section 8. Keep away from incompatible substances.

Precautions against fire and explosion:

Flammable vapors may accumulate and form explosive mixtures with air in containers, process vessels, including partial, empty

and uncleaned containers and vessels, or other enclosed spaces. Keep away from sources of ignition and do not smoke. Take

precautionary measures against electrostatic charging. Cool endangered containers with water.

Conditions for safe storage, including any incompatibilities

Conditions for storage rooms and vessels:

Make sure there is no possibility of entering the ground. Suitable material for storage containerts, casks and pipelines: stainless

steel . Unsuitable material for storage containers, casks and pipelines: steel , nonferrous metals . Protect against light. Observe

local/state/federal regulations.

Advice for storage of incompatible materials:

Observe local/state/federal regulations.

Further information for storage:

Store in a dry and cool place. Protect against moisture. Store container in a well ventilated place. Store in the dark. The effect of

direct sunlight or UV radiation must be completely ruled out, even during transit. In the product and in the gas space of the

container, a small quantity of oxygen must be present for stabilisation.

Minimum temperature allowed during storage and transportation: -20 °C

Maximum temperature allowed during storage and transportation: 50 °C

Transport information

Shippingopen allclose all
SpecialProvisionsopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Marine transport (UN RTDG/IMDG)

Shippingopen allclose all
Remarksopen allclose all
Shippingopen allclose all
Remarksopen allclose all

Additional transport information

Additional information
Special provisions / remarks / other:
Not regulated for transport

Exposure controls / personal protection

Control parameters

Maximum airborne concentrations at the workplace:

Material                     mg/m3

Aerosol - inhalable fraction       10,0

The aerosol limit specified is a recommendation should aerosol be formed during processing.

Exposure controls

Exposure in the work place limited and controlled

General protection and hygiene measures:

Observe standard industrial hygiene practices for the handling of chemical substances. Do not eat, drink or smoke when handling.

Personal protection equipment:

Respiratory protection

If inhalative exposure above the occupational exposure limit cannot be excluded, adequate respiratory protection equipment must

be used. Suitable respiratory equipment: Respirator with a full face mask, according to acknowledged standards such as EN 136.

Recommended Filter type: Gas filter type ABEK (certain inorganic, organic and acidic gases and vapors; ammonia/amines),

according to acknowledged standards such as EN 14387

In case of mist, spray or aerosol exposure wear suitable personal respiratory protection and protective suit. Suitable respiratory

equipment: Respirator with a full face mask, according to acknowledged standards such as EN 136.

Recommended Filter type: Combined filter type ABEK-P2 (certain inorganic, organic and acidic gases and vapors;

ammonia/amines; particles), according to acknowledged standards such as EN 14387

Observe the equipment manufacturer's information and wear time limits for respirators.

Eye protection

tight fitting protective goggles .

Hand protection

Gloves are required at all times when handling the material.

Recommended glove types: Protective gloves made of butyl rubber

thickness of the material: > 0,3 mm

Breakthrough time: > 480 min

Recommended glove types: Protective gloves made of nitrile rubber

thickness of the material: > 0,4 mm

Breakthrough time: 10 - 30 min

Please observe the instructions regarding permeability and breakthrough time which are provided by the supplier of the gloves.

Also take into consideration the specific local conditions under which the product is used, such as the danger of cuts, abrasion,

and the contact time. Note that, due to the numerous external influences (such as temperature), a chemically resistant protective

glove in daily use may have a service life that is considerably shorter than the measured break through time.

Skin protection

protective clothing .

Exposure to the environment limited and controlled

Prevent material from entering surface waters, drains or sewers and soil.

Further information for system design and engineering measures

Observe national regulatory requirements.

Stability and reactivity

Reactivity; Chemical stability; Possibility of hazardous reactions

If stored and handled in accordance with standard industrial practices no hazardous reactions are known.

Relevant information can possibly be found in other parts of this section.

Conditions to avoid

Possibility of spontaneous polymerization of unstabilized product by ambient temperature.

Incompatible materials

Radical initiators (peroxid, light, heat, heavy metal compounds) may cause polymerization.

Hazardous decomposition products

none known

Further information:

Product contains polymerization inhibitor.

Disposal considerations

Waste treatment methods



Material that cannot be used, reprocessed or recycled should be disposed of in accordance with Federal, State, and local

regulations at an approved facility. Depending on the regulations, waste treatment methods may include, e.g., landfill or


Uncleaned packaging


Completely discharge containers (no tear drops, no powder rest, scraped carefully). Containers may be recycled or re-used.

Observe local/state/federal regulations. Uncleaned packaging should be treated with the same precautions as the material.

Waste Disposal Legislation Ref.No.(EC)

It is not possible to determine a waste code for this product in accordance with the European Waste Catalogue (EWC) since it is

only possible to classify it according to how it is used by the customer. The waste code is to be determined within the EU in liaison

with the waste-disposal operator.